Skip to main content

Settings

Settings in the menu decides how BeepClock turns clock-ins and clock-outs into attendance: whether a shift may continue past midnight, whether forgotten exits are completed automatically, and whether reports round the times. Changes are saved separately in each card with Save.

Attendance configuration​

Multi-day attendance​

Turn on Allow multi-day attendance if shifts cross midnight, for example a night shift from 22:00 to 06:00.

  • On: an exit on the next day is joined with the entry of the previous day into one attendance, which belongs to the day of the entry. Set Maximum multi-day attendance duration to the longest shift you expect, for example 16:00. If the exit comes later than that after the entry, BeepClock records two separate attendances instead.
  • Off: every calendar day is separate. An entry at 22:00 without an exit on the same day is shown as a missing exit, and the exit after midnight starts a new day.

Multi-day attendance and automatic exit cannot be used together: turning on multi-day attendance turns off automatic exit.

The setting applies to entries recorded after you save it. Past days stay as they were.

Automatic exit​

When employees forget to clock out, Automatic exit completes the day for them. Turn it on and set the Automatic exit time, for example 17:00.

  • Shortly after midnight, BeepClock checks the previous day. Every employee who clocked in but did not clock out gets an exit at the configured time.
  • The exit is a real time entry of type Automatic. It counts like any other exit and is visible in the employee's attendance.
  • An employee whose last entry is later than the automatic exit time is not completed; fix those days on the Problems page.

To complete many forgotten exits at once without automatic exit, use the Problems page.

Rounding​

Rounding makes reports show times rounded to a chosen interval. It is shown only if rounding is enabled for your organisation.

Choose a Rounding mode:

ModeWhat is rounded
DisabledNothing; reports show exact times.
Round timestampsEvery clock-in and clock-out, including the start and end of breaks. You set the direction for clock-ins and clock-outs separately; break starts follow the clock-out direction and break ends the clock-in direction.
Round breaksThe length of each break; the rounded breaks are subtracted from the attendance.
Round daily totalOnly the net time worked in the day.

Then choose the Rounding interval (5, 10, 15, 30 or 60 minutes) and the direction: Up, Down or Nearest. For example, with timestamps rounded to the nearest 15 minutes, a clock-in at 08:07 is shown as 08:00 and a clock-out at 16:52 as 16:45. The Example table in Settings shows the effect of your choice before you save.

  • Rounding only changes what reports show: the daily list, the monthly report and the PDF, Excel and CSV summaries. The recorded entries are not changed, so you can change or turn off rounding at any time.
  • After saving, rounding applies to all reports, including past months.
  • Days with a missing entry or exit are not rounded until they are completed.
  • On the attendance pages, the Rounding active banner shows that rounding is on; Peek original values shows the exact times.

Location naming​

If your organisation uses locations, Location naming gives each level of the location tree its own name. See Locations.

FAQ​

Our night shift is split into two days. How do I fix it?
Turn on 'Allow multi-day attendance' in 'Settings' and set the maximum duration to the longest shift, for example 12:00. Shifts recorded from then on are joined into one attendance that belongs to the day of the entry. Days recorded before the change stay as they were.
Why didn't automatic exit add an exit right at the set time?
Automatic exit runs shortly after midnight and completes the previous day. The exit gets the configured time, but it appears in the attendance only after midnight.
Why can't I turn on automatic exit?
Automatic exit is not available while multi-day attendance is on. Turn off 'Allow multi-day attendance' first.
Does rounding change the recorded times?
No. Rounding only changes the times shown in reports. The recorded entries stay exact, and 'Peek original values' on the attendance pages shows them.
Why is one day not rounded?
Days with a missing entry or exit are not rounded. Complete the day, for example on the Problems page, and it is rounded in the reports.
I don't see the Rounding Policy card. Why?
Rounding has not been enabled for your organisation. Write to [email protected].
Who can change the settings?
If your organisation uses roles, opening Settings requires the 'Settings' permission and saving changes requires 'Change settings'. Location naming requires 'Manage locations'.